預壓儀是土木工程中專門用來提供土樣前期預壓工作的新型室內土工試驗儀器。其壓力源可采用液壓方式,穩定可靠,可*替代早期產品。那么它該如何使用?使用注意事項又有哪些呢?
預壓儀使用方法:
1、調整機架,使其水平,安定儀器。
2、檢查杠桿兩側與吊圈是否相摩擦,軸承翻滾應靈敏。調整平衡陀方位,使杠桿處于平衡狀況,調整時,用手扶正拉桿,目測杠桿根本水平,旋緊平衡陀并帽。旋開螺栓,與杠桿充沛脫開,并將杠桿處于立柱中間。
3、翻滾鋼球放入導軌中,翻滾靈敏無異物卡阻。
4、旋緊剪切盒上的螺絲插銷,鄙人框內放入透水石,用環刀切取土樣,修平兩端,環刀平口向下,用推土器將土樣推入剪切盒內,依次蓋上透水石,傳壓板。
5、將加壓框上的橫梁壓頭對準傳壓板,調整壓頭方位,使杠桿輕輕上抬,框架向后時,容器部分能自在取放。
6、安裝測力環、百分表。滾動頂頭,向前推動測力環,使加壓框處于筆直狀況,把固定座上的螺絲頂頭向前旋進,使之觸摸良好,鎖緊螺母。
7、按土工試驗規程逐次施加筆直壓力。
8、拔出插銷,滾動手輪,使上盒剛好觸摸量力環,百分表對零,一起將筆直移位百分表對零,旋動傳壓螺釘,適量抬高杠桿,若試樣未經預壓可略高,以免加后土樣下沉而使杠桿過于傾斜,刺進插銷。
9、待土樣受載或達到固結要求時,擰出剪切盒上的螺絲插銷,準備剪切。
10、按試驗要求挑選剪切速率。
11、將儀器電源插到電源插座上,將開關撥到【行進】檔,開始剪切,量力環百分表指針不再行進,或有撤退時記下數值,一般剪切位移應達到4mm左右。當剪切過程中百分表讀數無峰值時,則可剪至6mm。
12、試驗完畢后,將儀器整理歸位。剪切盒擦洗潔凈,外表涂以薄層防銹油。
預壓儀運用注意事項:
1、試驗完畢后,將剪切盒擦洗潔凈,有關外表涂以薄層防銹油。
2、量力環應根據運用情況或半年進行一次重新率定。
3、杠桿處軸承運用半年或根據運用情況應給予清洗涂黃油光滑4運用應變控制式直剪儀,要認真閱覽技能說明書,了解技能指標、工作性能、運用方法、注意事項,嚴格遵照儀器運用說明書的規定步驟進行操作。
5.初次運用應變控制式直剪儀人員,必須在熟練人員指導下進行操作,熟練掌握后方可進行獨立操作。
6.試驗時運用的預壓儀 要布局合理,擺放規整,便于操作,觀察及記載等。